Water fundamentals
Water-quality parameters, sampling, mass balance, flow measurement, treatment objectives and fit-for-purpose water quality.
Water Treatment Training
Build confident teams. Improve plant performance.
YWT India delivers practical, site-relevant training that helps operators, engineers and managers understand their water and wastewater systems, respond to abnormalities and run plants with greater safety, consistency and efficiency.
CompetenceClear understanding of process and equipment
ConsistencyStandard operating and monitoring practices
ResponseFaster recognition of abnormal conditions
PerformanceBetter control of water, energy and chemicals
Who should attend
Training for every level of plant responsibility
Content and depth are adjusted for the participants’ roles, experience and operating responsibilities.
Typical participants
- Plant operators
- Shift supervisors
- Utility engineers
- ETP/STP personnel
- Maintenance teams
- Laboratory teams
- EHS and compliance teams
- Engineering managers
Training modules
01
02
03
04
05
06
07
08
09
Select individual modules or build a complete programme
Programmes can cover one system, an integrated utility block or the complete water and wastewater cycle.
Raw-water treatment
Clarification, coagulation, flocculation, filtration, softening, disinfection, chemical preparation and operating checks.
Membrane systems
UF, NF and RO fundamentals, pretreatment, recovery, rejection, fouling, scaling, cleaning, preservation and troubleshooting.
ETP & biological treatment
Equalisation, physicochemical treatment, aeration, activated sludge/MBBR, nutrient balance, clarifiers and sludge handling.
STP & reuse systems
Biological treatment, tertiary filtration, disinfection, MBR where applicable, reuse quality and safe recycled-water management.
ZLD & evaporation
High-COD/high-TDS segregation, RO concentration, MEE/MVRE, ATFD, condensate quality, salt handling and operating interdependencies.
Cooling & boiler water
Cycles of concentration, blowdown, scaling, corrosion, microbiological control, boiler feedwater and condensate monitoring.
Instrumentation & automation
Flow, pressure, level, pH, conductivity, DO and ORP instruments, calibration awareness, PLC/SCADA trends and alarm response.
Safety & troubleshooting
Chemical handling, confined-space and rotating-equipment awareness, abnormal-condition response and structured root-cause analysis.
Programme development
A structured route from training need to workplace application
1Need reviewPlant, participants and performance gaps
2CustomisationModules, level, examples and duration
3DeliveryConcepts, demonstrations and discussion
4AssessmentQuestions, exercises and understanding check
5ApplicationActions, SOP focus and performance follow-up
Delivery formats
Choose the format that suits your team
The programme can combine classroom learning with direct observation of the participant’s own plant.
On-site plant training
Training linked to the actual process, equipment, SOPs, control philosophy, samples and operating data available at site.
Classroom workshop
Structured technical sessions with process diagrams, operating examples, exercises and question-and-answer discussions.
Online technical sessions
Focused modules, refresher training, troubleshooting discussions and multi-location participation through virtual delivery.
Programme outputs
Useful beyond the training room
The emphasis is on knowledge that can be applied to daily operation, maintenance coordination and performance review.
- Customised agenda and participant-level content
- Training material and plant-specific examples
- Operating-parameter and KPI guidance
- Troubleshooting logic and abnormal-condition response
- Knowledge assessment or participation record, when agreed
- Recommended follow-up actions for the plant team
Frequently asked questions
Planning your training programme
Can the training be customised to our existing plant?
Yes. Process flow diagrams, operating data, recurring issues, SOPs and participant experience can be reviewed to make the programme relevant to the actual installation.
Can operators and engineers be trained separately?
Yes. Operator training can focus on routines, observations, safety and first response, while engineering sessions can cover process calculations, control philosophy, optimisation and root-cause analysis.
Does YWT provide on-site practical training?
Yes, subject to agreed access and safety requirements. Classroom sessions can be combined with a guided plant walkdown and discussion of real operating conditions.
Can the programme cover more than one treatment system?
Yes. An integrated programme can connect raw water, utilities, ETP, STP, recycling, RO and ZLD so participants understand how changes in one block affect the others.
Build a programme around your plant and people.
Tell us the systems to be covered, participant profile, recurring operating concerns and preferred delivery format. YWT India will propose a focused training programme.
